Skip to content

xTool

79/100Score8 reviews

xTool S1

Diode laser engraverDesktop
Check price on Amazon

Amazon · xTool Official

S1 40W Black Rotary bundle

Check price on Amazon
View on Amazon

Research byResearch updatedResearch method

Buying verdict

Why consider it

The S1 has useful owner evidence for flat work and rotary craft projects. A 20W owner reports almost a year of cutting and engraving wood, black acrylic and leather; a separately equipped 40W owner praises focus and positioning. That rotary experience used the riser and rotary accessories, so match the bundle to the intended work.

Where it falls short

Smoke containment drew complaints from two owners using a riser or conveyor, including a 20W setup with outside extraction. LightBurn experiences also vary: reimporting a device profile restored one machine, while another 40W owner’s intermittent command failure remained unresolved. These accessory and software cases should be checked against the planned setup.

Also compare

  • WeCreat Vision Pro 45W — A 45W enclosed diode alternative with listed LiDAR autofocus.
  • xTool M2 — The M2 offers 10W, 20W or 40W diode configurations with automatic material probing.
Compare these models

40 W applications

Wood, leather & coated-material personalization

Product source ↗
Illustrative phone-style photo: small birch plywood coaster with dark laser-engraved flower pattern

Wooden keepsakes

Illustrative phone-style photo: natural tan leather patch with burned line artwork

Leather patches

Illustrative phone-style photo: opaque black acrylic square with a subtle engraved matte line design, NOT clear acrylic cutting

Dark-acrylic marks

Wood & coated materials; not clear-acrylic cutting.AI-generated examples

Software

  1. Add artwork
  2. Set power & speed
  3. Mark / engrave
xTool StudioFree core app

Windows & Mac

Source for Software ↗

Reviews & discussions

8 accounts

Additional owner accounts show a mixed picture: quick setup and useful engraving/fabric projects for some, alongside complaints about positioning, riser/conveyor smoke containment, long-job output and intermittent software commands. One account concerns a refurbished machine. These reports document buying considerations, not a measured satisfaction rate or a controlled performance comparison.

Read sources (4)

Reddit · Owner-reported case

S1 owner follow-up: positioning, smoke and long-job concerns

After an initially mixed setup report, this owner later regretted the purchase and reported frustration with positioning, smoke containment when using the riser or conveyor, and output consistency during longer jobs. These are one owner’s reports, not a measured defect rate.

S1 family owner using riser/conveyor accessories. The November 2023 and January 2024 posts are the same author and count as one account.

Read original source: S1 owner follow-up: positioning, smoke and long-job concerns ↗

Reddit · Owner-reported case

S1 40W: initial fabric test pieces

A new S1 40 W owner reported setting up the machine and making initial test pieces on 500D and 1000D fabric, with a positive first impression. This is a short initial-use account, not a durability study or evidence that every fabric is suitable.

The post explicitly names S1 40 W. No results are transferred to other xTool models or material safety claims.

Read original source: S1 40W: initial fabric test pieces ↗

Reddit · Owner-reported case

Refurbished S1 40W: setup and engraving experience

A refurbished S1 40 W buyer described connecting the machine, updating firmware and engraving a walnut bottle opener, followed by coasters, bookmarks and tags. The positive experience concerns one refurbished unit; its historical purchase price and condition are not evidence for current new-machine offers.

Named historical refurbished 40 W configuration. Exact equivalence to today’s new-machine bundles is unverified; the historical price is not added to purchase offers.

Read original source: Refurbished S1 40W: setup and engraving experience ↗

LightBurn Software Forum · Owner-reported case

S1 40W: recurring LightBurn command problem

An owner who had used an S1 40 W with LightBurn for over a year reported that the machine intermittently accepted only the Home command. The owner also described a separate riser-base exception in xTool Studio. The thread does not establish a confirmed cause or a resolution for that owner.

One named S1 40 W owner and their software/setup combination. Another participant’s later improvement is not treated as this owner’s repair outcome.

Read original source: S1 40W: recurring LightBurn command problem ↗
3Positive2Negative0Neutral3Mixed

Topics mentioned

Score

8 reviews
79 / 100

An editorial buying assessment of specifications, prices, after-sales terms and the quality and balance of firsthand experiences. This is not a laboratory test or a customer star rating.

Specifications30/30
Pricing evidence10/20
After-sales clarity20/20
Owner review evidence18.8/30
Evidence quality8/10
Reported experience10.8/20
3Positive2Negative3Mixed
8 independent accounts · 12/12 fields fully sourcedMethod ↗
Share your experience with this machine
Why this score

Specifications

Laser source
2.5/2.5
Wavelength
2.5/2.5
Output power
2.5/2.5
Electrical supply
2.5/2.5
Cooling
2.5/2.5
Dimensions
2.5/2.5
Machine weight
2.5/2.5
Working area
2.5/2.5
Marking speed
2.5/2.5
Mark detail
2.5/2.5
Software
2.5/2.5
Focus method
2.5/2.5

Pricing evidence

Named configuration & power
4/4
Seller & price source
4/4
Price recency
2/4
Verified power options
0/4
Two-channel power coverage
0/4

Reviews: evidence quality contributes 10 points and reported experience contributes 20. We average independent accounts; more reviews do not automatically earn more points. Sample size affects confidence only.

Mixed or unrated accounts use the experience midpoint; they are not counted as positive endorsements.

  • Documents a LightBurn alarm and configuration details; this software-specific case does not establish a hardware defect.

  • ducktapedaddy · Reddit ↗Mixed · Detailed use or test

    Describes almost a year of ownership, several materials, a riser and external extraction, with good results but persistent smoke leakage.

  • TheTikaani · Reddit ↗Mixed · Specific use account

    Names the 10 W module, 3 mm wood, power, speed and two passes, while explaining the limits of that lower-power configuration.

  • drd001 · Reddit ↗Positive · Detailed use or test

    Compares prior machines and explains focusing, software and timed rotary projects after several months of ownership.

  • PhysicalConsistency · Reddit ↗Negative · Detailed use or test

    A follow-up changes the earlier impression and describes specific positioning, smoke and long-job cooling complaints.

  • CSW_64 · Reddit ↗Positive · Brief impression

    Names two fabric grades and an initial setup, but gives no detailed settings or long-term results.

  • mkj5013 · Reddit ↗Positive · Detailed use or test

    Explains the refurbished condition, firmware setup and several engraving projects; the account is not evidence for current new-machine bundles.

  • mcotter11 · LightBurn Software Forum ↗Negative · Detailed use or test

    Gives the machine, software history, repeat-job failure and multiple troubleshooting steps, without a confirmed repair for this owner.

Owner reviews & discussions

LightBurn Software Forum · 2026-10-21 · kfitz0363 (Kevin) · Self-reported use

S1 owner restores operation after LightBurn profile reset

MixedSpecific use account

An S1 owner reports failure to fire after updating to LightBurn 2.2. In a follow-up they say removing the S1 profile and reimporting their old lbdev file restored operation; they also adjusted pointer offset. Power, module, firmware and bundle are unspecified. Another owner in the same discussion still reports problems.

Read the original discussion: S1 owner restores operation after LightBurn profile reset

Reddit · 2024-11-01 · ducktapedaddy · Self-reported use

S1 20W owner likes results but reports riser smoke leakage

MixedDetailed use or test

An owner with almost a year of S1 20W ownership praises detail and cutting and reports working with wood, black acrylic and leather. With a riser installed, smoke still escapes at its bottom despite a duct fan and outside hose. This ventilation observation concerns their riser and extraction installation; other bundles are not verified.

Read the original discussion: S1 20W owner likes results but reports riser smoke leakage

Reddit · 2024-10-29 · TheTikaani · Self-reported use

S1 10W owner cuts 3mm wood with two passes

MixedSpecific use account

An S1 10W owner reports successful cutting and engraving of 3mm wood, using 97% power, 9mm/s and two passes for cutting. They like XCS convenience but would have preferred more power. Wood species and exact bundle are not identified, so this is not a general material benchmark.

Read the original discussion: S1 10W owner cuts 3mm wood with two passes
More reviews & discussions (5)

Reddit · drd001 · Self-reported use

S1 40W owner praises positioning and rotary workflow

PositiveDetailed use or test

An experienced laser user identifies their S1 as a 40W unit with 2W IR, rotary, fire suppression, riser and honeycomb. They praise its focus and positioning and say their first rotary project took under 20 minutes. They find XCS easier to learn but less capable for drawing than LightBurn. Evidence concerns that configuration, not every S1 power or bundle.

Read the original discussion: S1 40W owner praises positioning and rotary workflow

Reddit · 2024-01-02 · PhysicalConsistency · Self-reported use

S1 owner follow-up: positioning, smoke and long-job concerns

NegativeDetailed use or test

After an initially mixed setup report, this owner later regretted the purchase and reported frustration with positioning, smoke containment when using the riser or conveyor, and output consistency during longer jobs. These are one owner’s reports, not a measured defect rate.

Read the original discussion: S1 owner follow-up: positioning, smoke and long-job concerns

Reddit · 2024-03-05 · CSW_64 · Self-reported use

S1 40W: initial fabric test pieces

PositiveBrief impression

A new S1 40 W owner reported setting up the machine and making initial test pieces on 500D and 1000D fabric, with a positive first impression. This is a short initial-use account, not a durability study or evidence that every fabric is suitable.

Read the original discussion: S1 40W: initial fabric test pieces

Reddit · mkj5013 · Self-reported use

Refurbished S1 40W: setup and engraving experience

PositiveDetailed use or test

A refurbished S1 40 W buyer described connecting the machine, updating firmware and engraving a walnut bottle opener, followed by coasters, bookmarks and tags. The positive experience concerns one refurbished unit; its historical purchase price and condition are not evidence for current new-machine offers.

Read the original discussion: Refurbished S1 40W: setup and engraving experience

LightBurn Software Forum · 2025-12-08 · mcotter11 · Self-reported use

S1 40W: recurring LightBurn command problem

NegativeDetailed use or test

An owner who had used an S1 40 W with LightBurn for over a year reported that the machine intermittently accepted only the Home command. The owner also described a separate riser-base exception in xTool Studio. The thread does not establish a confirmed cause or a resolution for that owner.

Read the original discussion: S1 40W: recurring LightBurn command problem

What specifications are published?

Rated power40 W
Full specifications

Listing 1

Cutting materialsPaper, Wood, Leather, MDF, Felt, Opaque acrylic, etc.Source ↗
Electrical (40W)25 V DC / 11 A adapter output for the listed 40 W configuration; check the regional adapter for mains input.Source ↗
Dimensions765 × 561 × 183 mm without riser base; 765 × 561 × 268 mm with riser base.Source ↗
Machine weight20 kg for the listed S1 40 W machine; excludes the separately listed 560 g infrared module.Source ↗
Working area498 × 319 mm for the S1 40 W module; other modules and conveyor setups have different usable areas.Source ↗
Marking speedUp to 600 mm/s seller-listed working speed; not an independently measured cutting speed.Source ↗
Spot size0.08 × 0.10 mm for the listed S1 40 W module; the 0.03 × 0.03 mm figure belongs to the optional infrared module.Source ↗
SoftwarexTool Creative Space (XCS) / LightBurn. LightBurn supports basic operations; some xTool-specific features are unavailable.Source ↗
Focus methodOne-click autofocus.Source ↗

Listing 2

Laser sourceBlue semiconductor diode laser; optional 2 W infrared module is sold separately.Source ↗
Wavelength455 nm blue-diode modules (10 W / 20 W / 40 W); excludes the optional infrared module.Source ↗
Rated power10 W / 20 W / 40 W blue-diode options; one selected laser module per configuration.Source ↗

Listing 3

Cooling (20W / 40W)Fan-cooled laser module, documented for the 20 W and 40 W modules.Source ↗
Source ↗