Welding capacity
Published model range
Not published
Shielding gas: Welding: 99.99% Nitrogen or 99.99% Argon Cutting/Cleaning: 99.99% Nitrogen or 99.99% Argon or Air
Shielding gas: Nitrogen / Argon
xTool
52/100Score15 reviewsManufacturer store · xTool official storefront
USD · tax & shipping extra · Recorded 2026-11-10
xTool MetalFab Laser Welder/ CNC Cutter / 800W / 800W Welder
$4,499Research byPickaLaserResearch updatedResearch method
The catalog separates 800W welding, 1200W welding and a 1200W welder-plus-CNC-cutter package. That makes the machine-versus-system cost visible.
The CNC work area belongs to the cutter package, not the handheld torch. Wide rust/paint cleaning requires the extra MaxClean accessory; standard post-weld cleaning is a different mode.
Steel fabrication, brackets & sheet-metal joints



Published model range
Not published
Shielding gas: Welding: 99.99% Nitrogen or 99.99% Argon Cutting/Cleaning: 99.99% Nitrogen or 99.99% Argon or Air
Shielding gas: Nitrogen / Argon
Air-cooled
A MetalFab owner reports a non-working machine and a week of troubleshooting before a dispute over the selling distributor’s support responsibility. xTool replies that it assists purchases from authorized distributors. The case shows why the seller of record matters; it does not establish a failure rate.
Reddit · Owner-reported case
mel_ancholee reports an unresolved laser-module error. An xTool representative replies that authorized-distributor purchases are supported and asks to check the seller’s status.
The owner is already counted in the catalog. The thread does not show a final repair outcome, and other xTool models are excluded.
Read original source: MetalFab downtime and distributor support ↗An editorial buying assessment of specifications, prices, after-sales terms and the quality and balance of firsthand experiences. This is not a laboratory test or a customer star rating.
Reviews: evidence quality contributes 10 points and reported experience contributes 20. We average independent accounts; more reviews do not automatically earn more points. Sample size affects confidence only.
Mixed or unrated accounts use the experience midpoint; they are not counted as positive endorsements.
The owner describes a nonworking MetalFab, clean lenses, a missing aiming light and a week of troubleshooting followed by a distributor-support dispute; no repair outcome is posted.
The thread documents an out-of-box Error 6, repeated troubleshooting, remote diagnosis and a working replacement; the owner praises support while describing email delays and return-before-replacement downtime.
The owner connects hissing and low-pressure cutting interruptions to a gas coupling, then confirms that replacement coupling and hose fixed the problem.
A six-month 1200W shop review identifies gas and compressor setup, stainless cutting and welding examples, slow engraving, software behavior and business use; the owner likes the system but criticizes cloud-storage prompts.
The owner reports rapid lens consumption, dross and loss of previously successful mild-steel cutting settings; material thickness, gas settings and a confirmed cause remain absent.
A 1200W owner reports about one hour of cutting before recurring weld-head power errors, and unsuccessful restart and support-guide checks; no resolution is documented.
The operator describes intermittent interlock faults, troubleshooting, a later failure during cleaning and lost work, while also praising the CNC and prior support; no final replacement outcome is supplied.
The comment confirms receipt and Error 7 while awaiting support, but gives no process settings, diagnosis, duration or repair outcome.
The owner supplies measured errors for three square sizes and confirms a support-provided fix; the actual calibration procedure and later production results are not reported.
The owner records lens replacement, Error 6 during steel welding, electrical checks and failed troubleshooting, then confirms a replacement within roughly two weeks and praise for the exchange support.
The thread follows a job-stopping laser fault through unanswered support and an advance-paid replacement, refund and bank fees; the replacement runs well but the owner remains dissatisfied with the exchange process.
The original YouTube comment could not be reopened in this audit. Existing curated owner context is retained with brief quality credit; settings, chronology and long-term performance are not independently reconstructed.
The original YouTube comment could not be reopened in this audit. Existing curated owner context is retained with brief quality credit; settings, chronology and long-term performance are not independently reconstructed.
The original YouTube comment could not be reopened in this audit. Existing curated owner context is retained with brief quality credit; settings, chronology and long-term performance are not independently reconstructed.
The original YouTube comment could not be reopened in this audit. Existing curated owner context is retained with brief quality credit; settings, chronology and long-term performance are not independently reconstructed.
Reddit · 2026-09-03 · mel_ancholee · Self-reported use
An owner reported about a week of downtime and was directed to the selling distributor. No final repair is recorded. The distributor's identity and authorization were not verified, so this cannot establish a blanket warranty refusal for third-party orders.
Read the original discussion: MetalFab: a distributor-purchased unit awaited repairReddit · 2026-07-28 · ResponsibilityNo1648 · Self-reported use
A UK owner reported Error 6 on arrival and a missed engineering appointment. They later twice confirmed that the replacement worked well and praised support. Their 800W UK configuration is not evidence for the US 1200W specifications or price.
Read the original discussion: MetalFab 800W UK: replacement resolved the initial errorReddit · 2026-06-15 · SithLard · Self-reported use
An otherwise satisfied owner reported leaking connections during long cuts, causing low-pressure stoppages. Their edited update said new fittings and a hose from the manufacturer fixed the problem immediately. Delivery time and costs were not disclosed.
Read the original discussion: MetalFab: replacement fittings resolved low-gas-pressure stopsReddit · 2026-05-20 · MuskratAtWork · Self-reported use
A roughly six-month user liked stainless-steel welding, 4 mm 304 cutting and MaxClean rust and paint removal. They disliked the 24 × 24 inch table, slow dot engraving and cloud-file prompts. This is a complete-package account, with no disclosed repair case or standalone welder failure rate.
Read the original discussion: MetalFab and CNC: useful mixed work, with a limited table and software frictionReddit · 2026-03-18 · Jefferomis · Self-reported use
An owner cutting mild steel reported rapid protective-lens consumption, dross and loss of cut-through at previously working settings. Support requested settings, lens and calibration details. There was no final owner-confirmed fix.
Read the original discussion: MetalFab CNC: lens consumption and cutting quality remained unresolvedReddit · 2026-02-28 · jezbeall · Self-reported use
After roughly a month of ownership and about one hour of cutting, the machine gave an error and could not be used. Official troubleshooting did not fix it. Support acknowledged the ticket, but no final repair result is recorded.
Read the original discussion: MetalFab 1200W: startup error with no final repair updateReddit · 2026-02-15 · samwizman · Self-reported use
An owner reported intermittent interlock trouble, followed by a loud noise, a tripped circuit and Error 7 during cleaning. They liked the CNC and had previously found support helpful, but were still seeking a replacement in the archived account.
Read the original discussion: MetalFab: interlock trouble followed by Error 7Reddit · 2026-01-28 · BirdzyNest · Self-reported use
An owner reported Error 7 and no output, then waited for support after troubleshooting. The same incident appeared in two posts; there is no final handling outcome.
Read the original discussion: MetalFab: Error 7 on the day after deliveryReddit · 2026-01-12 · Confident_Fall_1530 · Self-reported use
An owner found a one-axis size error in cut squares during the first week. After additional 100 mm and 200 mm tests requested by support, they confirmed the manufacturer's solution fixed it. This concerns CNC dimensional compensation, not weld quality or source life.
Read the original discussion: MetalFab CNC: support corrected a dimensional offsetReddit · 2025-12-27 · guy559 · Self-reported use
After limited CNC work, cutting stopped going through; a protective-lens change helped briefly, followed by Error 6 during welding. The owner later confirmed a replacement main unit arrived in about two weeks and praised the return collection. The replacement does not erase the initial faults.
Read the original discussion: MetalFab: a replacement arrived after cutting and welding faultsReddit · 2025-10-02 · ImpossibleGift9970 · Self-reported use
An owner lost output mid-job and initially experienced missed remote support and slow replies. They later received a cooler-running replacement that continued to work, but disliked paying before reimbursement and the bank fees and communication.
Read the original discussion: MetalFab: a working replacement, but a costly support processYouTube · @melgross · Self-reported use
The same commenter described one trouble-free week with a 1200W unit and elsewhere said it handled much of their welding, while thin wire still took practice. Other comments discussed wanting to buy. Relative dates and an edit leave the sequence uncertain; this is one account, without a verified ownership duration.
Original unavailable · Previous summary not reverified
Read the original review: MetalFab: positive use comments with an uncertain timelineYouTube · @tomcronininc · Self-reported use
An owner liked their MetalFab welder and wire feeder but had not used cutting and was asking how to switch modes. Their satisfaction does not establish CNC-table or cutting performance.
Original unavailable · Previous summary not reverified
Read the original review: MetalFab: satisfaction with welding, before trying cuttingYouTube · @tinbutcher61 · Self-reported use
An owner and an automotive-restoration colleague liked thin-sheet welding and finishing. They still needed practice and spare protective lenses, since smoke and dirt contaminated them. Follow-up operating comments belong to the same case; no warranty repair outcome was given.
Original unavailable · Previous summary not reverified
Read the original review: MetalFab 800W: positive automotive sheet-welding experienceYouTube · @GoremanX · Self-reported use
An otherwise satisfied owner said cleaning without MaxClean triggered intermittently on rusty or coated surfaces. A suggested workaround was not manufacturer-approved and is not treated as a repair. No completed service outcome was reported.
Original unavailable · Previous summary not reverified
Read the original review: MetalFab: intermittent cleaning contact on rust and coatingsYouTube · 2026-08-02 · SYLVESTERS CUSTOMS · Commercial review
SYLVESTERS CUSTOMS compared welding and finishing on automotive sheet and later demonstrated cutting and MaxClean. The operator found time savings but still needed gun control, weld-pool observation and heat management. xTool supplied the machine and an affiliate relationship was disclosed. Two videos form one case.
Original unavailable · Previous summary not reverified
Read the original review: MetalFab: useful automotive sheet work, with preparation and practiceYouTube · 2026-07-31 · Making Stuff · Commercial review
Making Stuff described nearly a year of use, including thin-material welding and aluminum cutting. They saw production value while stressing preparation and learning. The video includes affiliate links and a discount code, without a documented repair case.
Original unavailable · Previous summary not reverified
Read the original review: MetalFab and CNC: a creator's nearly year-long workflow accountYouTube · 2025-10-11 · TimWelds · Commercial review
TimWelds compared material workflows and reported overheating pauses when cutting steel with oxygen, unlike his compressed-air cutting. He explicitly had not needed after-sales service. Sponsorship and affiliate relationships were disclosed; a service-network description is not a repair outcome.
Original unavailable · Previous summary not reverified
Read the original review: MetalFab: oxygen cutting paused for heat in a sponsored testYouTube · 2025-05-24 · Chad’s Custom Creations · Commercial review
Chad's Custom Creations showed MetalFab use and argued against judging the process from one failed test. The samples and bends are personal demonstrations, not structural certification or proof that other negative reports are false. An affiliate relationship was disclosed.
Original unavailable · Previous summary not reverified
Read the original review: MetalFab: personal sample tests, with an affiliate relationshipYouTube · 2025-03-24 · Laser Engraving 911 · Commercial review
Laser Engraving911 tried welding, cutting and the CNC setup at an xTool demonstration space. The video discusses size, speed and learning and contains referral links. It is not a long-term self-purchased ownership or repair account.
Original unavailable · Previous summary not reverified
Read the original review: MetalFab and CNC: a showroom trial rather than long-term ownership| Rated power | 800 W |
|---|
| Laser source | Fiber Laser |
|---|---|
| Rated power | 1200W |
| Working area | 24.02 × 24.02 in (610 × 610 mm) |
| Fiber cable | 196.85 in (5 m) |
| Machine weight | 38.2 kg |
| Dimensions | 28.66 × 12.87 × 20.16 in (728 × 327 × 512 mm) |

SFX
Air cooling keeps a water-cooling loop out of the setup. Requires a 220V supply.

Sky Fire Laser
Air cooling keeps a water-cooling loop out of the setup. Requires a 220V supply.

Gweike
Air cooling keeps a water-cooling loop out of the setup.

OMTech
The handheld head can be brought to the workpiece. Plan for water-cooling setup and maintenance.