Welding capacity
Published specification
Not published
Shielding gas: Nitrogen / Argon / Air
XLaserlab
72/100Score6 reviewsAmazon · Xlaserlab Official
X1 Pro 700W
Check price on AmazonResearch byPickaLaserResearch updatedResearch method
The published air-cooled design and 100–250 V input make site setup a useful comparison point. Owners describe actual sample welds, including a prepared carbon-steel root pass.
Early aluminum attempts and awkward wire guidance appear in owner accounts. Neither a successful prepared joint nor a 3-in-1 label proves suitability for every thickness or a qualified weld procedure.
Steel fabrication, brackets & sheet-metal joints



Published specification
Not published
Shielding gas: Nitrogen / Argon / Air
Air-cooled
X1 Pro owners report useful sample welds and a successful prepared root pass, alongside awkward wire guidance and unsuccessful early aluminum attempts. Cleaning light contamination was useful, while heavier rust and coatings needed more work. These job-specific reports do not establish long-term reliability or a qualified welding procedure.
Reddit · Owner-reported case
Ok-Fill-8925 confirms buying the X1 Pro. Small weld samples produced a narrow heat zone, but wire alignment and access were awkward. The owner reports smoke and residue after cleaning and unsuccessful early aluminum trials.
Verified comment dated 13 November 2026. Self-reported early trials, not measured penetration, coating-removal performance or a validated welding procedure.
Read original source: X1 Pro: useful sample welds, awkward wire feed ↗Reddit · Owner-reported case
SaiTek64 explicitly identifies an X1 Pro and shares carbon-steel sample settings while asking for advice on travel speed.
The same author already has a report in the catalog; this second thread does not count as another owner. Published settings are not universal recommendations.
Read original source: A 700W X1 Pro operator practices wire-fed welds ↗Reddit · Owner-reported case
Taukstofish reports an easy root pass on prepared carbon steel with a 700W Xlaserlab Pro and no problems so far. The user explicitly has no service experience and only speculates about durability in shop dust.
The beveled joint and land preparation are part of this one self-reported job. This is not proof of general 3/8-inch penetration or a qualified weld procedure.
Read original source: 700W X1 Pro: a shop user reports a useful root pass ↗An editorial buying assessment of specifications, prices, after-sales terms and the quality and balance of firsthand experiences. This is not a laboratory test or a customer star rating.
Reviews: evidence quality contributes 10 points and reported experience contributes 20. We average independent accounts; more reviews do not automatically earn more points. Sample size affects confidence only.
Mixed or unrated accounts use the experience midpoint; they are not counted as positive endorsements.
The owner identifies a 700W X1 Pro and describes reflective aluminum and uncertainty about pulse settings; no completed comparison or durability test is supplied.
An architectural shop reports about six months of X1 Pro Ultimate use and a problem resolved to its satisfaction, but does not explain the defect, repair or welding settings.
The original YouTube comment could not be reopened in this audit. Existing curated owner context is retained with brief quality credit; settings, chronology and long-term performance are not independently reconstructed.
The original YouTube comment could not be reopened in this audit. Existing curated owner context is retained with brief quality credit; settings, chronology and long-term performance are not independently reconstructed.
The owner separates cleaning, cutting and sample weld trials, describing smoke and residue, wire alignment, awkward access, promising small welds and unsuccessful aluminum attempts; these are early trials.
A shop user names the 700W Xlaserlab Pro and describes a beveled carbon-steel root weld with joint preparation and a positive result; service and long-term shop durability remain untested.
Reddit · 2026-06-10 · SaiTek64 · Self-reported use
A new user asked about reflections and weld-pool behavior while welding aluminum and found the manual's temperature and failure boundaries unclear. There is no long-term production, repair or service outcome in the account.
Read the original discussion: X1 Pro 700W: an early aluminum-welding questionReddit · 2026-01-20 · billybigboot · Self-reported use
An owner found the machine useful in an architectural metalworking shop after roughly six months. They reported one unspecified problem that the manufacturer handled to their satisfaction. The parts, cost, timing and repair steps were not disclosed.
Read the original discussion: X1 Pro: useful in a metalworking shop after six monthsYouTube · @chrisb-888 · Self-reported use
A commenter said they bought through Kickstarter, liked the equipment and lent it to a friend working on cars. Association is to the model family discussed in the video; power, bundle and repair experience were not confirmed.
Original unavailable · Previous summary not reverified
Read the original review: X1 Pro: a positive Kickstarter buyer commentYouTube · @DangerousDaveKincaid · Self-reported use
A commenter described their own X1 Pro as useful but limited in bead size or thickness capability and said they had accidentally welded a part to the table. The comment concerns the X1 Pro, even though it appears under a MetalFab video.
Original unavailable · Previous summary not reverified
Read the original review: X1 Pro: useful welding within a limited bead sizeReddit · 2026-11-13 · Ok-Fill-8925 · Self-reported use
Ok-Fill-8925 confirms buying the X1 Pro. Small weld samples produced a narrow heat zone, but wire alignment and access were awkward. The owner reports smoke and residue after cleaning and unsuccessful early aluminum trials.
Read the original discussion: X1 Pro: useful sample welds, awkward wire feedReddit · Taukstofish · Self-reported use
Taukstofish reports an easy root pass on prepared carbon steel with a 700W Xlaserlab Pro and no problems so far. The user explicitly has no service experience and only speculates about durability in shop dust.
Read the original discussion: 700W X1 Pro: a shop user reports a useful root passYouTube · 2025-12-04 · Alec Steele · Commercial review
Alec Steele demonstrated welding, cleaning and cutting and adjusted firmware or settings during the trial. Adapting to the gun, wire feed and parameters took work. XLaserlab sponsored the video; this short trial cannot establish long-term reliability or warranty handling.
Original unavailable · Previous summary not reverified
Read the original review: X1 Pro: sponsored thin-steel tests needed setup adjustmentsYouTube · 2025-09-19 · Halfass Kustoms · Commercial review
Halfass Kustoms compared an X1 Pro with an older 1500W machine and documented spot alignment, wire-spool fit and handling. Results were specific to the settings and samples, not proof of general 700W-to-1500W equivalence. Referral links or discounts were present; no long-term repair case was shown.
Original unavailable · Previous summary not reverified
Read the original review: X1 Pro: calibration and wire-spool fit took attentionYouTube · 2025-08-09 · TimWelds · Commercial review
TimWelds tested steel, stainless steel and aluminum. Thin material suited the machine better than thicker aluminum; he noted a large gun and wire-retraction snagging. Cleaning could mark the substrate. The break test was not a welding certification, and referral links and a discount code were disclosed.
Original unavailable · Previous summary not reverified
Read the original review: X1 Pro: promising thin material, with limits on thicker aluminum| Rated power | 700 W |
|---|
| Machine weight | Machine Weight: 21 kg |
|---|

Sky Fire Laser
Air cooling keeps a water-cooling loop out of the setup.

Gweike
Air cooling keeps a water-cooling loop out of the setup.

SFX
Air cooling keeps a water-cooling loop out of the setup. Requires a 220V supply.

Sky Fire Laser
Air cooling keeps a water-cooling loop out of the setup. Requires a 220V supply.