Working area
Published specification
Twotrees
54/100Score4 reviewsAmazon · Twotrees-US Official Store
A budget open-frame engraver with a 300 × 300 mm area and an air-assist nozzle. A nozzle is not an air pump; confirm the pump and protective setup you will need.
TTS-55 Pro; 5.5W; air-assist nozzle
Check price on AmazonResearch byPickaLaserResearch updatedResearch method
For patient photo and small craft engraving, the 5.5W TTS-55 Pro has a listed 300 × 300 mm bed and LightBurn/LaserGRBL support. One anonymous seller-hosted reviewer reported good photo engraving after tuning over three months; treat that as an individual account rather than a repeatable benchmark.
Cutting can demand patience: that reviewer needed at least five passes through their thin plywood, without precise thickness or settings. Two separate owners reported early weak or absent laser output, including one completed refund. Neither case confirms the failed component or establishes a failure rate for the TTS-55 Pro.
Wood, leather & coated-material engraving



Published specification
Cooling not published
Windows only
Windows & Mac
Owner evidence is mixed: a three-month user liked photo engraving after tuning but needed at least five passes for thin plywood. Separate owners report early weak/no laser output, including one Amazon refund. A curve-engraving complaint behaved differently in LaserGRBL, so it is not confirmed as a hardware fault.
LightBurn Software Forum · Owner-reported case
The owner could not engrave circles or text in LightBurn but did not see the same behavior in LaserGRBL. Replies questioned the LightBurn installation; no completed repair or confirmed cause appears.
Explicit TTS-55 Pro account with comparative software testing. Community suspicions are not proof of a machine defect or a software diagnosis.
Read original source: Curves failed in LightBurn; another software path differed ↗TwoTrees owner review · Owner-reported case
After three months the user says engraving works well once settings are tuned. Cutting their thin plywood took at least five passes, and photo engraving still needed time with the 5.5W head.
Current TTS-55 Pro product page, review UUID 40bb3740-8528-481d-a15d-1cbb6db27587. Anonymous and not purchase-verified; the reviewer’s thickness wording is imprecise and is not promoted to a cutting specification.
Read original source: Good photo engraving, slow thin-plywood cuts ↗Reddit · Owner-reported case
The new owner says the laser worked three times and then stopped emitting while the gantry still moved. A follow-up notes a missing green indicator. Contacting support is suggested, but no fix is confirmed.
The original post names TTS 55 Pro. Other comments with unspecified or non-Pro models are not counted; this isolated case does not establish a failure rate.
Read original source: Motion continued after the laser stopped emitting ↗Reddit · Owner-reported case
After assembly the beginner could not obtain useful laser strength despite trying online fixes. They returned it to Amazon, received a refund and ordered from TwoTrees; the thread does not report the new machine’s result.
Explicit TTS-55 Pro owner and completed marketplace refund. Reports about other people’s modules and the separate TTS20 comment are not additional cases.
Read original source: Weak output ended in a refund; replacement not yet tested ↗An editorial buying assessment of specifications, prices, after-sales terms and the quality and balance of firsthand experiences. This is not a laboratory test or a customer star rating.
Reviews: evidence quality contributes 10 points and reported experience contributes 20. We average independent accounts; more reviews do not automatically earn more points. Sample size affects confidence only.
Mixed or unrated accounts use the experience midpoint; they are not counted as positive endorsements.
The owner supplies comparison images and tests LightBurn output against LaserGRBL, naming the TTS-55 Pro. Replies suspect an unofficial software build, but the owner does not confirm the diagnosis or final fix.
The anonymous seller-hosted text states three months of 5.5W use and contrasts photo engraving with at least five passes on thin plywood. It gives a useful material-specific limit, but no speed/power settings and no verified-buyer badge.
The named TTS-55 Pro owner reports three successful uses followed by no beam while motion remains active, and follows up about the module indicator lights. The thread has no verified repair outcome or identified failed component.
The TTS-55 Pro buyer describes weak output after assembly, attempted online fixes and an actual Amazon refund, followed by a new order. The refund outcome is concrete; the claimed defective module is not technically diagnosed and the replacement was still pending.
LightBurn Software Forum · 2025-03-24 · friend4all · Self-reported use
The owner could not engrave circles or text in LightBurn but did not see the same behavior in LaserGRBL. Replies questioned the LightBurn installation; no completed repair or confirmed cause appears.
Read the original discussion: Curves failed in LightBurn; another software path differedTwoTrees owner review · 2026-09-11 · Self-reported use
After three months the user says engraving works well once settings are tuned. Cutting their thin plywood took at least five passes, and photo engraving still needed time with the 5.5W head.
Read the original discussion: Good photo engraving, slow thin-plywood cutsReddit · casiomarlim · Self-reported use
The new owner says the laser worked three times and then stopped emitting while the gantry still moved. A follow-up notes a missing green indicator. Contacting support is suggested, but no fix is confirmed.
Read the original discussion: Motion continued after the laser stopped emittingReddit · 2024-12-31 · North-Register-5788 · Self-reported use
After assembly the beginner could not obtain useful laser strength despite trying online fixes. They returned it to Amazon, received a refund and ordered from TwoTrees; the thread does not report the new machine’s result.
Read the original discussion: Weak output ended in a refund; replacement not yet tested| Rated power | 5.5 W |
|---|---|
| Working area | 300 × 300 mm |
| Software | LightBurn |
| Dimensions | 10 × 4.97 × 7 inches |
| Working area | 300 × 300 mm |
|---|---|
| Software | LightBurn |
| Rated power (quoted module) | 5500 mW (5.5W) |
| Dimensions | 10 × 4.97 × 7 inches |
| Laser source | 5.5W diode laserSource ↗ |
|---|---|
| Rated power | 5.5 WSource ↗ |
| Electrical | 100–240 V AC, 50/60 Hz; adapter output 12 V DC / 4 ASource ↗ |
| Dimensions | 570 × 510 × 150 mmSource ↗ |
| Machine weight | 3.2 kg (current product page)Source ↗ |
| Working area | 300 × 300 mmSource ↗ |
| Max speed | 30000 mm/minSource ↗ |
| Spot size | 0.08 × 0.08 mmSource ↗ |
| Software | LightBurn / LaserGRBLSource ↗ |

SCULPFUN
LightBurn is supported.

ORTUR
LightBurn is supported.

SCULPFUN
LightBurn is supported.

Creality
Autofocus handles the focusing step.