Skip to content

Gweike

61/100Score3 reviews

Gweike G1

Diode laser engraverDesktop
$239

Manufacturer store · Gweike official online store

View seller

USD · tax & shipping extra · Recorded 2026-11-10

gweike G1 10W laser cutter& engraver

$239
View seller

Research byResearch updatedResearch method

Buying verdict

Why consider it

Consider the G1 for a 10W diode with a listed 410 × 310 mm bed and a LightBurn workflow. One owner praised engraving quality despite coordinate problems; another restored operation by changing LightBurn transfer mode to synchronous. That remedy applies to the reported setup, not every G1 configuration.

Where it falls short

The owner cases point to setup and motion checks before committing a large job. One G1 needed a coordinate workaround, while a specifically named 10W unit shifted larger engravings at 100 mm/s despite handling small coasters. The suspected motor fault was not diagnosed, so these reports do not establish a common hardware defect.

Also compare

Compare these models

10 W applications

Wood, leather & coated-material personalization

Product source ↗
Illustrative phone-style photo: small birch plywood coaster with dark laser-engraved flower pattern

Wooden keepsakes

Illustrative phone-style photo: natural tan leather patch with burned line artwork

Leather patches

Illustrative phone-style photo: opaque black acrylic square with a subtle engraved matte line design, NOT clear acrylic cutting

Dark-acrylic marks

Wood & coated materials; not clear-acrylic cutting.AI-generated examples

Owner feedback

3 accounts
0Positive1Negative0Neutral2Mixed

Topics mentioned

Score

3 reviews
61 / 100

An editorial buying assessment of specifications, prices, after-sales terms and the quality and balance of firsthand experiences. This is not a laboratory test or a customer star rating.

Specifications27.5/30
Pricing evidence8/20
After-sales clarity10/20
Owner review evidence15.1/30
Evidence quality8.2/10
Reported experience6.9/20
1Negative2MixedSmall sample
3 independent accounts · 11/12 fields fully sourcedMethod ↗
Why this score

Specifications

Laser source
2.5/2.5
Wavelength
2.5/2.5
Output power
2.5/2.5
Electrical supply
2.5/2.5
Cooling
0/2.5
Dimensions
2.5/2.5
Machine weight
2.5/2.5
Working area
2.5/2.5
Marking speed
2.5/2.5
Mark detail
2.5/2.5
Software
2.5/2.5
Focus method
2.5/2.5

Pricing evidence

Named configuration & power
2/4
Seller & price source
4/4
Price recency
2/4
Verified power options
0/4
Two-channel power coverage
0/4

Reviews: evidence quality contributes 10 points and reported experience contributes 20. We average independent accounts; more reviews do not automatically earn more points. Sample size affects confidence only.

Mixed or unrated accounts use the experience midpoint; they are not counted as positive endorsements.

  • brentL (Brent L) · Maker Forums ↗Mixed · Detailed use or test

    Explains the G1 coordinate offset, homing position, test shapes and a workspace workaround, without a confirmed underlying fix.

  • Reports an alarm after initial tests and later identifies a buffered-to-synchronous setting change that helped that owner.

  • WalkerGaming413 · Reddit ↗Negative · Specific use account

    Names the G1 10 W and engraving speed and follows up on larger-job skipping; the suspected motor failure is not a confirmed diagnosis.

  • 2 after-sales policy areas remain unconfirmed.
  • Small review sample; reported experiences may not represent other buyers.
Owner reviews & discussions

Maker Forums · 2025-11-19 · brentL (Brent L) · Self-reported use

G1 engraving works but coordinates do not match

MixedDetailed use or test

A new G1 owner says engraving quality is good, but machine coordinates and LightBurn coordinates disagree despite reinstalling and checking limits. They describe a workaround using an oversized software bed. Laser power, hardware revision and purchased bundle are not specified.

Read the original discussion: G1 engraving works but coordinates do not match

LightBurn Software Forum · 2024-09-22 · zoick (Cameron) · Self-reported use

G1 owner resolves an alarm with transfer-mode change

MixedSpecific use account

After successful small tests, a G1 owner could no longer frame or engrave because of an alarm lock. They report resolving their issue by changing LightBurn transfer mode to synchronous. A second G1 owner in the thread still reports a hard-limit error. Power and machine revisions are unspecified.

Read the original discussion: G1 owner resolves an alarm with transfer-mode change

Reddit · WalkerGaming413 · Self-reported use

G1 10W owner reports image shifting

NegativeSpecific use account

An owner explicitly identifies a Gweike G1 10W diode and reports lateral shifts while engraving at 100 mm/s. They say smaller coasters work but larger burns shift, suspect a motor problem and decide to upgrade. The cause is unconfirmed; accessory bundle and hardware revision are unknown.

Read the original discussion: G1 10W owner reports image shifting

What specifications are published?

Rated power10 W
Full specifications

Model specifications

Max speed400mm/s
Power draw120w24v5A
Machine weightMachine Weight: 6.6KG

Listing 2

Precision0.01mmSource ↗
Laser sourceBlue diode laserSource ↗
Wavelength450 nmSource ↗
Rated power10 W optical output; 120 W machine inputSource ↗
Electrical24 V DC / 5 A (120 W input)Source ↗
Dimensions613 × 590 × 160 mmSource ↗
Machine weight6.6 kgSource ↗
Working area410 × 310 mmSource ↗
Marking speedUp to 400 mm/sSource ↗
Spot size0.08 × 0.06 mmSource ↗
SoftwareLightBurn (USB)Source ↗
Focus methodManual focus blockSource ↗
Source ↗